SMART-81 Printer Firmware 2025.05.30
Detail
▼
▲
[ 1.02.65 ]
- Fixed the misaligned position issue of the K panel during Partial printing (300x600, 1200 Mode) when using a YMCK ribbon.
- Modified the Separation Mode 0 Logic:
Existing Logic: Only K panel prints → Head-up → Separation is performed at the same printing speed (K panel behaves the same as Separation Mode 2).
New Logic: Only K panel prints → Separation is performed at the same printing speed → Head-up (K panel behaves the same as Separation Mode 3).
- Added a function to display a warning on the LCD Display when the Inner Stack is full of error cards.
(Settable via CardPrinterConfig.exe / Extra tab / Inner Stack Full Warning LCD (ON, OFF))
- Modified the code to generate an error when the Error Card Out is set to the Inner Stack and the Inner Stack is full of cards.
(Settable via CardPrinterConfig.exe / Extra tab / Inner Stack Full Error Ignore (ErrCheck, ErrIgnore))
[ 1.02.58 ]
- Fixed the issue where the printer sent Top lamination commands when the Laminator settings were set to Bottom or Both.
(The code was modified to send the Bottom lamination command when Bottom Side lamination is performed.)
- Improved cases where an error could occur during Mono Printing and Ribbon Search operations when the HopperCaseOpen is detected.
(During printing, Ribbon Search only stops when Printer CaseOpen or BackSideCoverOpen is detected.)
[ 1.02.54 ]
- Modified the code to turn the heater off during MAG Read and then turn it back on or off depending on its previous state after the read is complete.
[ 1.02.51 ]
- Fixed an issue where the Tag Count Down was not performed at the bottom side during YMCKK color double-sided printing.
- Added a 70 Single Hopper Front Device.
- Changed the heater control maximum temperature from 200°C MAX to 220°C MAX
(the Heater Temperature CTL logic was modified).
- Disabled Wait Temperature
(IDLE temperature control now operates using the Retransfer Operating Temperature).
- Modified the logic for searching for Film position during retransfer and improved the issue of under-wound film during partial print separation.
- Modified the logic for calculating the outer diameter when printing with K (mono) ribbon.
(For Mono ribbons, it always operates as 3 regardless of the Separation Mode setting.)
- Added a Ribbon and Film Tag Error Count (cumulative) LCD display function.
- Added the Heater Serial Num display function to the LCD Menu.
- Added the Retransfer Issue Count display and Clear functions to the LCD Menu.
[ 1.02.44 ]
- Added the CardPrinterConfig-Extra-K Panel Anti-Tear setting.
(Allows selection of whether to immediately drive (ON) or use a Delay (OFF) for the Ribbon Motor when printing the K, K2(YMCKK) panels.)
[ 1.02.43 ]
- Fixed the bug where the Unlock operation was not performed when executing Unlock Printer via Printer Properties → Service Tab while the printer was in TagErr status.
[ 1.02.41 ]
- Added Dot Compensation Value to tune the density deviation for each device based on the number of dots used.
[ 1.02.40 ]
- Fixed the card jamming issue of the Flipper.
- Added FlipHold Mode
(When OutPosSen detects a card, FlipMotor Hold activates / upon card release, FlipperRepos operation performs, and then the motor is Free).
- Implemented AutoRearCardIn feature
(the AutoRearIn function is Disabled until the Card Release is performed).
- Fixed the issue of the film skipping one panel during K ribbon double-sided printing.
- Modified K ribbon Separation Mode 0, 2, 3
(Now operates with the same logic as the K panel of the YMCK ribbon).
- Improved color density variation between 600 DPI Heads and density variation during continuous printing.
[ 1.02.33 ]
- Modified the Separation Mode operation (Mode 0, 2).
- Modified the Ribbon Motor to start driving immediately when printing K, K2(YMCKK) panels
(for other panels, it drives after printing the set Line, same as the previous version).
- Modified the Ribbon Motor Max Torque to 6000 when printing K, K2(YMCKK) panels.
- Modified the K2 panel ribbon search behavior when using the YMCKK Type.
- Improved the issue of the film skipping one panel when printing in SBS Mode and then printing again immediately.
- Added Stability Mode (When the mode is ON, the "lightning" phenomenon is improved, but the time increases by about 1 second per panel).
- Improved printing density variation during continuous printing at 300 DPI.
[ 1.02.21 ]
- added the Strobe Threshold feature for 300 DPI K panel (default: 80%)
- added to improve retransfer quality at low temperatures by checking to the BD temperature
- modified to improve vertical lines when printing gradation images
- modified that the print roller is also moved when the film is moved from the LCD operation menu while the case is open
[ 1.02.17 ]
- enhanced the printing quality about density on 600DPI SMART-81H when printing in a row
- changedd the logic that error shows after printing job is finished when the error occurs on SMART-81L with SMART-81P+L combination
- enhanced the logic to search the I panel when YMCKI ribbon is installed
- added the logic to enable the Clean Printer function when BendRemedy is installed
[ 1.02.14 ]
- enhanced the initializing process when turning on
- added the status code when PRINT DATA FAIL occurs (Error occurs when real installed ribbon Type and RibbonType in printing data is different)
[ 1.02.12 ]
- changed the code of RF TAG CountDown
- added the Error flag about LAM Thread operation
[ 1.02.10 ]
- added the function to show the progress to ###% format on LCD panel when Initialize & reInitialize(When Case Open & Close)
- fixed the code of RF TAG R/W communication (When RF communication failed, register hopping and recover the code error)
- fixed the bug of EXT communication
[ 1.01.13 ]
- Supported 600 DPI PrintHead (S81H)
- Changed to allow the SBSCommand while preheating process
- Changed the Separtion Mode 3
- Changed the default value of Lock
- Changed the SBSCardOut function when BendRemedy installed
- Changed the logic of YMCKK ribbon searching
[ 1.01.06 ]
- Added the TagTest function on LCD panel
- Improved the Tag Read/Write functions
- Fixed the bug of CardOutBin action
- Fixed the bug that can't get Dump
- Fixed the bug to show System Ready in advance before the finish of PreHeating
- Fixed the bug to show the wrong film manufacturer on Service tab of the printer driver
[ 1.01.01 ]
- Added the function to move a card based on the sensor while retransferring a Film
- Added the function to set the retransferring/Standby temperature on LCD panel
- Added the function to set the start/target temperature of PreHeating, and Timeout when Preheating
- Improved the issue that Film is torn
- Changed the criteria of PreHeating function
- Fixed the bug of 'Network Config - DataAbort'
- Fixed the bug of Tag Countdown
- Fixed the bug that BendRemedy can't be turned off in the printer driver
[ 1.00.96 ]
- Added to function to Clean on LCD panel
- Fixed the bug of Cleaning function
[ 1.00.92 ]
- Supported the 600DPI printing
- Supported the BendRemedy module
- Supported the YMCK Split function
- Added the SBS Command of Lam HeadUp/Down
- Added the SBScommand for BendRemedy
- Added the Tag Erase function, LockPassword initializing function
- Improved the Rf CountDown action
[ 1.00.71 ]
- Changed the wait position of the card to the right side of the retransfer roller after the card-in action
- Changed the wait position of the card to the right side of the retransfer roller when backside printing on Fastest Mode
- Modified the status from error to normal even if Hopper Cartridge is opened when 'Count Zero' message is shown
[ 1.00.68 ]
- Added the function to adjust the Tag Gain automatically
- Changed the Seperation Mode 3 action
- Modified to CardOut action to hold a card even if Repositioning a card
- Modified the CardOut Sensor Filter time to 50ms
- Modified to speed of film detect action, saved to Backup
