-
SMART-81 Printer Firmware 2025.12.04
Detail
▼
▲
[ 1.02.65 ]
- Fixed the misaligned position issue of the K panel during Partial printing (300x600, 1200 Mode) when using a YMCK ribbon.
- Modified the Separation Mode 0 Logic:
Existing Logic: Only K panel prints → Head-up → Separation is performed at the same printing speed (K panel behaves the same as Separation Mode 2).
New Logic: Only K panel prints → Separation is performed at the same printing speed → Head-up (K panel behaves the same as Separation Mode 3).
- Added a function to display a warning on the LCD Display when the Inner Stack is full of error cards.
(Settable via CardPrinterConfig.exe / Extra tab / Inner Stack Full Warning LCD (ON, OFF))
- Modified the code to generate an error when the Error Card Out is set to the Inner Stack and the Inner Stack is full of cards.
(Settable via CardPrinterConfig.exe / Extra tab / Inner Stack Full Error Ignore (ErrCheck, ErrIgnore))
[ 1.02.58 ]
- Fixed the issue where the printer sent Top lamination commands when the Laminator settings were set to Bottom or Both.
(The code was modified to send the Bottom lamination command when Bottom Side lamination is performed.)
- Improved cases where an error could occur during Mono Printing and Ribbon Search operations when the HopperCaseOpen is detected.
(During printing, Ribbon Search only stops when Printer CaseOpen or BackSideCoverOpen is detected.)
[ 1.02.54 ]
- Modified the code to turn the heater off during MAG Read and then turn it back on or off depending on its previous state after the read is complete.
[ 1.02.51 ]
- Fixed an issue where the Tag Count Down was not performed at the bottom side during YMCKK color double-sided printing.
- Added a 70 Single Hopper Front Device.
- Changed the heater control maximum temperature from 200°C MAX to 220°C MAX
(the Heater Temperature CTL logic was modified).
- Disabled Wait Temperature
(IDLE temperature control now operates using the Retransfer Operating Temperature).
- Modified the logic for searching for Film position during retransfer and improved the issue of under-wound film during partial print separation.
- Modified the logic for calculating the outer diameter when printing with K (mono) ribbon.
(For Mono ribbons, it always operates as 3 regardless of the Separation Mode setting.)
- Added a Ribbon and Film Tag Error Count (cumulative) LCD display function.
- Added the Heater Serial Num display function to the LCD Menu.
- Added the Retransfer Issue Count display and Clear functions to the LCD Menu.
[ 1.02.44 ]
- Added the CardPrinterConfig-Extra-K Panel Anti-Tear setting.
(Allows selection of whether to immediately drive (ON) or use a Delay (OFF) for the Ribbon Motor when printing the K, K2(YMCKK) panels.)
[ 1.02.43 ]
- Fixed the bug where the Unlock operation was not performed when executing Unlock Printer via Printer Properties → Service Tab while the printer was in TagErr status.
[ 1.02.41 ]
- Added Dot Compensation Value to tune the density deviation for each device based on the number of dots used.
[ 1.02.40 ]
- Fixed the card jamming issue of the Flipper.
- Added FlipHold Mode
(When OutPosSen detects a card, FlipMotor Hold activates / upon card release, FlipperRepos operation performs, and then the motor is Free).
- Implemented AutoRearCardIn feature
(the AutoRearIn function is Disabled until the Card Release is performed).
- Fixed the issue of the film skipping one panel during K ribbon double-sided printing.
- Modified K ribbon Separation Mode 0, 2, 3
(Now operates with the same logic as the K panel of the YMCK ribbon).
- Improved color density variation between 600 DPI Heads and density variation during continuous printing.
[ 1.02.33 ]
- Modified the Separation Mode operation (Mode 0, 2).
- Modified the Ribbon Motor to start driving immediately when printing K, K2(YMCKK) panels
(for other panels, it drives after printing the set Line, same as the previous version).
- Modified the Ribbon Motor Max Torque to 6000 when printing K, K2(YMCKK) panels.
- Modified the K2 panel ribbon search behavior when using the YMCKK Type.
- Improved the issue of the film skipping one panel when printing in SBS Mode and then printing again immediately.
- Added Stability Mode (When the mode is ON, the "lightning" phenomenon is improved, but the time increases by about 1 second per panel).
- Improved printing density variation during continuous printing at 300 DPI.
[ 1.02.21 ]
- added the Strobe Threshold feature for 300 DPI K panel (default: 80%)
- added to improve retransfer quality at low temperatures by checking to the BD temperature
- modified to improve vertical lines when printing gradation images
- modified that the print roller is also moved when the film is moved from the LCD operation menu while the case is open
[ 1.02.17 ]
- enhanced the printing quality about density on 600DPI SMART-81H when printing in a row
- changedd the logic that error shows after printing job is finished when the error occurs on SMART-81L with SMART-81P+L combination
- enhanced the logic to search the I panel when YMCKI ribbon is installed
- added the logic to enable the Clean Printer function when BendRemedy is installed
[ 1.02.14 ]
- enhanced the initializing process when turning on
- added the status code when PRINT DATA FAIL occurs (Error occurs when real installed ribbon Type and RibbonType in printing data is different)
[ 1.02.12 ]
- changed the code of RF TAG CountDown
- added the Error flag about LAM Thread operation
[ 1.02.10 ]
- added the function to show the progress to ###% format on LCD panel when Initialize & reInitialize(When Case Open & Close)
- fixed the code of RF TAG R/W communication (When RF communication failed, register hopping and recover the code error)
- fixed the bug of EXT communication
[ 1.01.13 ]
- Supported 600 DPI PrintHead (S81H)
- Changed to allow the SBSCommand while preheating process
- Changed the Separtion Mode 3
- Changed the default value of Lock
- Changed the SBSCardOut function when BendRemedy installed
- Changed the logic of YMCKK ribbon searching
[ 1.01.06 ]
- Added the TagTest function on LCD panel
- Improved the Tag Read/Write functions
- Fixed the bug of CardOutBin action
- Fixed the bug that can't get Dump
- Fixed the bug to show System Ready in advance before the finish of PreHeating
- Fixed the bug to show the wrong film manufacturer on Service tab of the printer driver
[ 1.01.01 ]
- Added the function to move a card based on the sensor while retransferring a Film
- Added the function to set the retransferring/Standby temperature on LCD panel
- Added the function to set the start/target temperature of PreHeating, and Timeout when Preheating
- Improved the issue that Film is torn
- Changed the criteria of PreHeating function
- Fixed the bug of 'Network Config - DataAbort'
- Fixed the bug of Tag Countdown
- Fixed the bug that BendRemedy can't be turned off in the printer driver
[ 1.00.96 ]
- Added to function to Clean on LCD panel
- Fixed the bug of Cleaning function
[ 1.00.92 ]
- Supported the 600DPI printing
- Supported the BendRemedy module
- Supported the YMCK Split function
- Added the SBS Command of Lam HeadUp/Down
- Added the SBScommand for BendRemedy
- Added the Tag Erase function, LockPassword initializing function
- Improved the Rf CountDown action
[ 1.00.71 ]
- Changed the wait position of the card to the right side of the retransfer roller after the card-in action
- Changed the wait position of the card to the right side of the retransfer roller when backside printing on Fastest Mode
- Modified the status from error to normal even if Hopper Cartridge is opened when 'Count Zero' message is shown
[ 1.00.68 ]
- Added the function to adjust the Tag Gain automatically
- Changed the Seperation Mode 3 action
- Modified to CardOut action to hold a card even if Repositioning a card
- Modified the CardOut Sensor Filter time to 50ms
- Modified to speed of film detect action, saved to Backup
-
SMART-81 Laminator Firmware 2024.06.20
Detail
▼
▲
[1.00.38]
- Enhanced the RF TAG R/W communication code (Increased retry count when failed)
- Applied the temperature profile while Heating (Enhanced the waiting time of heating)
- Changed the waiting time of heating to the lami temperature, 90 -> 55sec
[1.00.36]
- Supported the Bend Remedy module
[1.00.35]
- Added the BaudRate 19200 Setting (Force Mode)
- Added the function to get the heating temperature of the laminator from the Printer
- Modified the action to do nothing when opening a Hopper Cartridge under 'Count Zero' status
-
SMART-81 Bend Remedy Firmware 2024.02.14
-
SMART-70 Printer Firmware 2024.11.29
Detail
▼
▲
[ 1.02.68 ] - 241120
- changed YMCKO ribbon color detection algorithm
[ 1.02.64 ] - 230217
- added the function to test the communication between modules into LCD panel
- added the function to recover the communication automatically when communi. error occurs
- added the function to show the counter of recoverring the communication in LCD panel
- added the function to show the error flag when communication error occurs between MS R/W board
- added the PC authentification mode
- supported the YMCPKO ribbon
- modified the function not to check device link error while printing (Prohibit the communication error)
- fixed the start position and scale is not proper when 600 & 1200 DPI printing
- fixed the calibration is slow when the ribbon count is not matched when K ribbon printing
[ 1.02.52 ] - 200221
- added the function to get a Job ID that printing is finished in the PC
- changed the escape time from 5 to 10 sec when LCD menu button isn't clicked
[ 1.02.50 ] - 190226
- fixed the bug that ribbon balance doesn't count after ribbon count down error occurs.
[ 1.02.49 ] - 181113
- added the 'Auto Cancel' option that cancel the printing data when error occurs
[ 1.02.41 ] - 170414
- modified the time to scan the encoder
[ 1.02.40 ] - 170411
- modified the standard value of the sensing a color
- added the software filter that Card In/Out sensor checks the position.
[ 1.02.33 ] - 160713
- added the Ballys mode when magnetic encoding
- added the one-pass print mode
[ 1.02.26 ] - 160126
- added the maximum combination that 2 printers and 2 laminators are used, IPFPFLFLO
- modified the function that Data Option Error occurs when the printing data is mismatched with combination
- fixed the bug that the multi termination error occurs by noise
-
SMART-70 Laminator Firmware 2025.01.17
-
SMART-70 Hybrid Flipper Firmware 2020.08.21
-
SMART-70 In & Output Hopper Firmware 2017.07.27
-
SMART-70 MS Encoder Firmware 2020.08.21
-
SMART-70 Multi-Hopper Firmware 2024.12.16
Detail
▼
▲
[ 1.00.36 ]
- activated CardMoveMotion function
[ 1.00.32 ]
- fixed the error information showing alternating Card In and Error when all hoppers have no cards
-
SMART-51,31 & 21 Printer Firmware 2024.10.02
Detail
▼
▲
[ 1.02.95 ]
- modified to show the firmware version and serial number in the LCD on SMART-51
[ 1.02.92 ]
- fixed the Card Out error when booting on with the laminator attached
[ 1.02.90 ]
- fixed the function to set the error card bin (3rd tray) if the compact multi-hopper is installed and the inner tray option is activated
when the initialization and Card Out command to the front side
[ 1.02.87 ]
- fixed the function to send the data on the normal readable MS track except for the track that MS read error occurs
- added the function to adjust the RMP value automatically when YMCKO (100) ribbon is installed
- changed the criteria of color detect level when P-ribbon is installed to fix the YMCKOK ribbon issue with SMART-31
- added the function to print a long card with up to 120mm width
- added the function to print a rewritable card without erasing on SMART-31R
[ 1.02.73 ]
- added the high-speed mode when printing rewritable card first time (6 - 7sec)
[ 1.02.72 ]
- supported the extra internal hopper in the SMART-70 multi-hopper (KIOSK)
- added the function to control the SMART-70 multi-hopper directly (KIOSK)
[ 1.02.64 ]
- fixed the bug that print position on panel is shifted depending on the amount of ribbon remaining.
- fixed the bug that printing wasn't counted when 600, 1200 DPI with K ribbon
- supported the YMCKOKR ribbon
- supported the compact multi hopper on the driver
- added the function to set the direction of the cleaning process
- added the function to set the Public key in the Laminator
- added the logic to occur init error when flipper out sensor detects a card while initializing
- modified the option to fix the direction of cleaning to backside if the multi-hopper is installed
- modified the option to consider the panel is black if the RGB value is under 85% with BO ribbon
- modified the logic that considers the card is inserted after Card In action even though Card In sensor doesn't detect a card on SBS mode & portable mode
- modified the logic to enter the cleaning process that Top cover is opened and ribbon is removed when booting up while right LED button is pushing
- fixed the bug that the K ribbon doesn't count the printing issue on 600 & 1200 DPI
-
SMART-51 & 31 Flipper Firmware 2024.02.13
-
SMART-51 Laminator Firmware 2024.02.13
Detail
▼
▲
[ 0.02.07 ]
- The S51L can work even though the laminating film is not inserted or the film balance is 0.
(S51 Printer firmware should be 1.02.72 or above)
-
SMART-30 & 50 Printer Firmware 2018.05.30
-
SMART Printer Ethernet Firmware 2025.12.04
Detail
▼
▲
[ OS: 2.4.054 // FS: 2.5.295 ]
- Modified so that both the existing command script and the new command script operate during dual-sided printing using OCP.
[ OS: 2.4.054 // FS: 2.5.219 ]
- Added the DrawTextCustom command, which fixes an issue where text position shifts downward when drawing text using a Custom Font.
[ OS: 2.4.054 // FS: 2.5.178 ]
- Supported dual-sided printing for SMART 51 line, SMART-70, and SMART-81 (300/600 DPI) using OCP.
- Fixed an issue that occurred during printing using SMART-81 OCP.
- Supported the PrintSampleCard OCP command for SMART-81 (600 DPI).
[ OS: 2.4.054 // FS: 2.4.332 ]
- Supported SMART-81 600 DPI.
[ OS: 2.4.054 // FS: 2.4.117 ]
- Enabled the selection of the TLS version.
- Enabled the use of HID RF readers (OK5122, OK5127).
-
SMART-50 Laminator Firmware 2016.12.14
